Emerson VSG & VSSG Spécifications Page 124
- Page / 162
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
11 – 10
Section 11 • Alarms, Trips, Status Information & Troubleshooting
Single Screw Compressor PLC Operation Manual • Vilter/Emerson • 35391CM
Trip Message Cause(s) Notes
(T015) Trip: Low Oil Injection
Temperature
Oil Injection Temperature is Below
"Oil Injection Temperature" Low Trip
Setpoint after compressor has com-
pleted pre-lube and warm up stages.
(T016) Trip: High Oil Injection
Temperature
Oil Injection Temperature exceeds
"Oil Injection Temperature" High Trip
Setpoint
(T017) Trip: Low Process
Temperature
Process Temperature falls below
Process Temperature Low Trip
Setpoint in Process Temperature
control or if displaying Process
Temperature.
Active if controlling or displaying
Process Temperature
(T018) Trip: (Unassigned)
(T019) Trip: (Unassigned)
(T020) Trip: Low Liquid Refrigerant
Temperature
Liquid Refrigerant Temperature
falls below Liquid Refrigerant
Temperature Low Trip Setpoint
if displaying Liquid Refrigerant
Temperature
Active if displaying Liquid Refrigerant
Temperature
(T021) Trip: Low Suction Pressure
Stpt. 1
Setpoint 1 is selected and Suction
Pressure falls below Suction Pressure
Low Trip Setpoint.
(T022) Trip: Low Suction Pressure
Stpt. 2
Setpoint 2 is selected and Suction
Pressure falls below Suction Pressure
Low Trip Setpoint.
(T023) Trip: High Discharge Pressure
Stpt. 1
Setpoint 1 is selected and Discharge
Pressure falls below Discharge
Pressure High Trip Setpoint.
(T024) Trip: High Discharge Pressure
Stpt. 2
Setpoint 2 is selected and Discharge
Pressure falls below Discharge
Pressure High Trip Setpoint.
(T025) Trip: Low Net Oil Pressure
- Run
Net Oil Pressure (Oil Manifold
Pressure - Suction Pressure) falls
below Net Oil Pressure Low Trip
Setpoint after prelube and warmup
are complete.
(T026) Trip: Failed To Reach Prelube
Pressure - Start Sequence Aborted
Failed to maintain required prelube
pressure for required time during
start-up.
(T027) Trip: High Oil Filter
Differential - Start
Oil Filter Differential (Filter In
Pressure - Oil Manifold Pressure)
exceeds Oil Filter Differential - Start
High Trip Setpoint when compres-
sor is running and before Oil Filter
Differential Start-Run Changeover
Timer expires.
- Single Screw Compressor PLC 1
- Important Message 4
- Table of Contents 5
- List of Tables and Figures 10
- HOW TO USE THIS MANUAL 13
- ADDITIONAL IMPORTANT NOTES 13
- Glossary of Terms 14
- 23 678 5 19
- Wiring Requirements 21
- Overview 23
- Operational Descriptions and 24
- Diagrams 24
- COMPRESSOR STARTUP SEQUENCE 25
- AUTO START-STOP 26
- ANTI-RECYCLE 26
- CAPACITY SLIDE CONTROL 26
- OPERATING MODES 30
- DISCHARGE 31
- PRESSURE 31
- SUCTION 31
- VFD CAPCITY CONTROL 32
- VOLUME SLIDE CONTROL 32
- SAFETIES 32
- EMERGENCY STOP 32
- OIL HEATERS 33
- OIL DRAIN SOLENOID 33
- 2-WAY OIL MIXING VALVE 34
- OIL INJECTION VALVE 34
- OIL COOLER TEMPERATURES 35
- OIL COOLER STANDBY HEATER 35
- EVAPORATIVE CONDENSER 37
- OIL COOLER 38
- CONDENSER 39
- WATER COOLED GAS AFTERCOOLER 40
- WATER COOLED CONDENSER 41
- LIQUID INJECTION VALVE 42
- VPLUS LIQUID INJECTION PUMP 43
- DISCHARGE RECYCLE VALVE 44
- ECONOMIZER SOLENOID(S) 45
- HOTGAS BYPASS SOLENOID 45
- VENTURI OIL RECOVERY 45
- GAS SCRUBBERS 45
- BUILDING ENCLOSURE DEVICES 46
- PERIODIC SLIDE VALVE EXERCISE 46
- Section 3 • Overview Screens 47
- 3 – 8 / Blank 54
- Section 4 • HMI Navigation 55
- 4 – 10 / Blank 64
- DATE AND TIME 66
- REMOTE OPERATION 66
- PANELVIEW CONFIGURATION 68
- INITIAL RUNNING DATA 68
- DEVICE NAMES 68
- BACK TO MENU 68
- Editing Device Names 69
- INSTRUMENTATION 70
- ALARM AND TRIP 71
- Calibration Main Screen 73
- Pressure Calibration Screen 74
- CALIBRATE PRESSURE INSTRUMENT 75
- OPTION 1 75
- OPTION 2 75
- Slide Calibration Screen 78
- Figure 6-8. Actuator Assembly 80
- Figure 6-9. Photo-chopper 81
- 6 – 10 / Blank 82
- Setpoints and Control Screens 83
- Compressor Control Setpoints 84
- MAIN MOTOR VFD 86
- DISCHARGE PRESSURE CONTROL 87
- CAPACITY SLIDE VALVE 87
- AUTO START/STOP 88
- ANTI-RECYCLE 89
- START UP 89
- SHUT DOWN 89
- PART TIME OIL PUMP 90
- LOAD LIMITS 90
- VOLUME SLIDE ADJUSTMENT 90
- MAIN MOTOR FLA 90
- OIL SEPARATOR HEATERS 90
- 7 – 10 / Blank 92
- Alarm and Trip Setpoints 93
- Oil Mixing Valve Screen 95
- Aftercooler Screens 98
- Condenser Screens 101
- Volume Slide Details Screen 107
- Start Menu Popup Screen 108
- IO/Comms Diagnostics Screen 109
- Event List Screen 110
- 10 – 6 / Blank 114
- Alarm Listing 115
- Alarm Message Cause(s) Notes 117
- Trip Listing 123
- Trip Message Cause(s) Notes 124
- Status Message Notes 130
- Troubleshooting 134
- Communication with a Central 135
- Controller/DCS 135
- Compressor PLC 135
- Pressure Units 136
- Temperature Units 136
- Alarm and Trip Data 142
- Interface Tag Description 143
- Status Data 150
- States of Discrete I/O 154
- Table 12-8. State Indicator 159
- Table 12-9. Mode Indicator 159
Produits connexes et manuels pour Compresseurs d'air Emerson VSG & VSSG
(10 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.653 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels