Emerson Liebert Remote Monitoring Panel Manuel d'utilisateur Page 88
- Page / 144
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
System and Control Options
Liebert
®
Universal Monitor
™
80
9.11 Manual Output Ctrl
The Manual Output Ctrl feature allows you to manually change the state of any digital output to ON
or OFF, overriding automatic control by the Liebert Universal Monitor (the default setting for all
outputs). This menu also allows you to release the manual override, returning any output to
automatic control.
There are two ways to override automatic control of outputs:
• Use the Manual Output Ctrl menu, as described in this section, to turn any output ON or OFF.
• Use the switch on the Liebert Universal Monitor board (see 1.7 - Controller Board Overview)
to force all eight outputs ON at the same time. (Note: This has no effect on the optional
Expansion Board outputs.)
After an output is forced manually ON or OFF through the Manual Output Ctrl menu, it remains in
that state until returned to automatic control through this menu.
Table 34 summarizes the four types of control, including the abbreviated message that appears on
the LCD and in log reports.
To force an output point ON or OFF or return it to automatic control:
Log In and Choose Manual Output Ctrl
• From the Main Menu, use the arrows
↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows
↑↓ to choose
Manual Output Ctrl, then press Enter ↵.
Select an Output
The Select Output menu, shown at right, display the current status
of all eight outputs.
• Use the arrows
↑↓ to choose the output you want—for example,
Output01—and press Enter ↵.
Turn Output ON or OFF / Return to Automatic
• From the Override Output menu, use the arrows
↑↓ to choose one
of these options:
• Auto (return to automatic control)
• Man ON (manually turn this output ON)
• Man OFF (manually turn this output OFF)
• Press Enter ↵.
Table 34 Automatic / manual control - output points
Message Description
AUTO Automatic Controlled by Liebert Universal Monitor
MAN ON Manually ON
This output forced ON or OFF
via Manual Output Ctrl menu
MAN OFF Manually OFF
HW MAN ON
Manually ON
(all outputs)
All outputs forced ON
via hardware switch on circuit board
Main Menu
VIEW STATUS
> SYSTEM AND CONTROL
↑↓=NEXT
↵=SELECT
Login
LOGIN
AAAA
↑↓=SELECT ↵=NEXT/END
System & Control Menu
SETUP SYSTEM
> MANUAL OUTPUT CTRL
CLEAR ALARMS & LOGS
↑↓=NEXT
↵=SELECT
Select Output
OVERRIDE OUTPUT
> OUTPUT01 AUTO
OUTPUT02 AUTO
↑↓=NEXT ↵=SELECT
OUTPUT03 AUTO
OUTPUT04 MAN ON
OUTPUT05 AUTO
OUTPUT06 AUTO
OUTPUT07 MAN OFF
OUTPUT08 AUTO
OUTPUT09 AUTO
OUTPUT10 MAN ON
OUTPUT11 AUTO
OUTPUT12 AUTO
OUTPUT13 MAN OFF
OUTPUT14 AUTO
OUTPUT15 AUTO
OUTPUT16 AUTO
Override Output
SELECT OUTPUT01
AUTO
↑↓=SELECT ↵=END
NOTE: OUTPUT09-OUTPUT16
for optional Expansion Board
- Universal Monitor 1
- TABLE OF CONTENTS 3
- 7.0 VIEW STATUS OPTIONS 4
- 10.0 SPECIFICATIONS 5
- 1.0 INTRODUCTION 9
- ALL CIRCUITS; 10
- ALL CIRCUITS: 11
- 1.7 Controller Board Overview 12
- POWER INPUT 14
- RELAY OUTPUTS 14
- 1.9 LED Indicators 15
- K4K3K2K1 K5 K6 K7 K8 16
- 1.11 Typical Sequence 17
- 2.0 INSTALLATION - MAIN BOARD 18
- Required tools 19
- 2.2.1 Mounting the Panel 19
- 2.3.1 Mounting the Panel 20
- Input Power Connections 22
- Packing Contents 24
- 3.2.1 Mounting the Panel 25
- 3.3.1 Mounting the Panel 26
- 4.1 Wiring Specifications 28
- (BOTTOM) 29
- 4.3 Connecting Analog Inputs 30
- TB10: COMMS 31
- 4.5 EIA422 Liebert SiteScan 32
- Web Connector 32
- 5.1 Wiring Specifications 33
- S4 S3 S2 S1 34
- EIA485 + (to UM-) 34
- EIA485 - (to UM+) 34
- POWER INPUT RELAY OUTPUTS 35
- 29 Liebert 37
- 6.0 OVERVIEW OF MENUS 38
- 6.1 Opening Screen Overview 39
- 6.2 Main Menu Overview 39
- 6.3 LCD Menu Overview 39
- 7.1 View Active Alarms 41
- 7.2 View Alarm Log 42
- 7.3 View Event Log 43
- 7.4 View Trend Log 44
- 7.5 View Input Status 45
- 7.6 View Output Status 46
- 7.7 View Pager Numbers 47
- 9.1 Login 51
- ↑↓=NEXT ↵=SELECT 52
- ↑↓=SELECT ↵=NEXT/END 52
- 9.2 Setup System - Overview 53
- 9.3.5 Set Up Delay Time 55
- 9.5.3 Change Units Label 58
- 9.5.4 Change 4 mA Value 59
- 9.5.5 Change 20 mA Value 59
- 9.5.6 Change Offset Value 59
- 9.5.9 Change Low Setpoint 61
- 9.5.10 Change High Setpoint 61
- 9.5.11 Set Up Delay Time 62
- Supported Modem Settings 68
- Default Modem Settings 68
- Configuring the Modem 68
- 9.9.1 Change Password 77
- Change the Password 77
- 9.9.3 Setup Site ID 78
- 9.9.4 Connect Battery 78
- 9.9.8 Factory Defaults 84
- 9.11 Manual Output Ctrl 88
- 9.12 Clear Alarms & Logs 89
- 9.12.3 Clear the Event Log 90
- 9.12.4 Clear the Trend Logs 90
- 85 Liebert 93
- A.2.1 Connection Methods 94
- A.2.2 Create a Connection 95
- COM1 Port Setup 96
- Properties Setup 97
- ASCII Setup 97
- A.3 OVERVIEW OF MENUS 99
- A.4 VIEW STATUS MENUS 100
- A.4.1 View Active Alarms 101
- A.4.2 View Alarm Log 102
- A.4.3 View Event Log 103
- A.4.4 View Trend Log 104
- A.4.5 View Input Status 105
- A.4.6 View Output Status 106
- A.4.7 View Pager Numbers 107
- Main Menu 108
- Back Up Alarm Log File 109
- Back Up Event Log File 110
- Back Up Trend Log Files 111
- A.6 SETUP MENU 112
- Setup Menu 113
- A.6.1 Setup Input 114
- A.6.2 Setup Common Alarm 116
- A.6.3 Setup Sensor 117
- Setup Sensor (continued) 118
- A.6.4 Setup I/O Matrix 119
- A.6.5 Setup Output 125
- Pager Setup 127
- Modem Setup 128
- A.6.7 Setup System Info 129
- Change Password 129
- Setup Site ID 130
- Connect Battery 131
- Setup Service Phone Number 132
- Factory Defaults 133
- Initiate Remote Alarm Test 134
- A.6.8 Connect Expansion Board 135
- A.6.9 Override Output 136
- Clear Active Alarms 138
- Clear the Alarm Log 138
- Clear the Event Log 139
- Clear the Trend Logs 139
- SL-31060_REV3_02-13 144
Produits connexes et manuels pour Unités d'alimentation électrique Emerson Liebert Remote Monitoring Panel
(48 pages)
(106 pages)© 2020, manymanuals.fr. Tous droits réservés | 4.645 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels