Emerson Liebert Remote Monitoring Panel Manuel d'utilisateur Page 32
- Page / 144
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Wiring and Connections - Main Board
Liebert
®
Universal Monitor
™
24
4.4 Connecting Common Alarm Outputs
The common alarm relay, found in the top right corner of the Liebert
Universal Monitor, permits the user to connect auxiliary notification
equipment, such as lights, horns and sirens, to the Liebert Universal
Monitor. To determine the proper wire size, see Table 7 - Wiring
specifications - main board.
There are two connectors for the common alarm output. However,
the connectors are not individual relay outputs. The connectors
should be treated as a double-pole, double-throw (DPDT) relay.
The common alarm relay is energized whenever an alarm occurs.
To connect an output:
1. Turn OFF electrical power to the Liebert Universal Monitor.
2. If necessary, remove a conduit knockout to permit wire entry into the Liebert Universal Monitor
enclosure.
3. Bring the wire(s) into the Liebert Universal Monitor enclosure through a conduit knockout or
access slot.
4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.
5. Tighten the screw until it holds the wire snugly.
4.5 EIA422 Liebert SiteScan
®
Web Connector
The Liebert Universal Monitor will interface with Liebert’s
SiteScan Web enterprise monitoring system. Liebert SiteScan can
be used to monitor analog and digital equipment from a host
computer and also to perform some configuration.
To connect the Liebert SiteScan host computer to the Liebert
Universal Monitor:
1. Turn OFF electrical power to the Liebert Universal Monitor.
2. If necessary, remove a conduit knockout to permit wire entry
into the Liebert Universal Monitor enclosure.
3. Bring the wire(s) into the Liebert Universal Monitor enclosure
through a conduit knockout or access slot.
4. Loosen the appropriate screw and slip the stripped end of the
wire into the terminal block.
5. Tighten the screw until it holds the wire snugly.
4.6 Communications Connections
The Liebert Universal Monitor Service Terminal Interface
offers full configuration and monitoring capability via the
RS232 port and the phone line connector (see
A.2 - Connecting to the Service Terminal Interface). The
phone line connector is also used for pager notifications and
service phone number options.
4.6.1 RS232 Connector
The RS232 port requires a null modem cable. Connect one end
of the cable to the Liebert Universal Monitor’s RS232 port, as
shown at right, and the other end to the COM1 port of a laptop
computer or video terminal.
4.6.2 Phone Line Connector
The Phone Line Connector requires an RJ11 connector.
Connect one end of the connector to the Liebert Universal
Monitor’s phone line connector, shown at right, and the other end to a telephone wall jack.
TB5: COMMON ALARM
(TERMINAL BLOCKS ROTATED IN VIEW)
(BOTTOM)
Q11
R26
R402
P11
+
C
C
NO
CC NO
MO
N ALARM
S
EN
S
TOP
ENABLE
AUDIBLE
(TOP)
NO C NC NO C NC
Common alarm outputs
485
+
—
+
—
(TOP)
(BOTTOM)
TB1
0
:
CO
MM
S
422
EIA422 Liebert SiteScan
Web connector
4
+
(TOP)
(BOTTOM)
TB10: COMMS
RJ11: PHONE
PIN 3-TIP
PIN 4-RING
MODEM
Serial interface connector
(RS232/EIA574)
Phone line
connector
- Universal Monitor 1
- TABLE OF CONTENTS 3
- 7.0 VIEW STATUS OPTIONS 4
- 10.0 SPECIFICATIONS 5
- 1.0 INTRODUCTION 9
- ALL CIRCUITS; 10
- ALL CIRCUITS: 11
- 1.7 Controller Board Overview 12
- POWER INPUT 14
- RELAY OUTPUTS 14
- 1.9 LED Indicators 15
- K4K3K2K1 K5 K6 K7 K8 16
- 1.11 Typical Sequence 17
- 2.0 INSTALLATION - MAIN BOARD 18
- Required tools 19
- 2.2.1 Mounting the Panel 19
- 2.3.1 Mounting the Panel 20
- Input Power Connections 22
- Packing Contents 24
- 3.2.1 Mounting the Panel 25
- 3.3.1 Mounting the Panel 26
- 4.1 Wiring Specifications 28
- (BOTTOM) 29
- 4.3 Connecting Analog Inputs 30
- TB10: COMMS 31
- 4.5 EIA422 Liebert SiteScan 32
- Web Connector 32
- 5.1 Wiring Specifications 33
- S4 S3 S2 S1 34
- EIA485 + (to UM-) 34
- EIA485 - (to UM+) 34
- POWER INPUT RELAY OUTPUTS 35
- 29 Liebert 37
- 6.0 OVERVIEW OF MENUS 38
- 6.1 Opening Screen Overview 39
- 6.2 Main Menu Overview 39
- 6.3 LCD Menu Overview 39
- 7.1 View Active Alarms 41
- 7.2 View Alarm Log 42
- 7.3 View Event Log 43
- 7.4 View Trend Log 44
- 7.5 View Input Status 45
- 7.6 View Output Status 46
- 7.7 View Pager Numbers 47
- 9.1 Login 51
- ↑↓=NEXT ↵=SELECT 52
- ↑↓=SELECT ↵=NEXT/END 52
- 9.2 Setup System - Overview 53
- 9.3.5 Set Up Delay Time 55
- 9.5.3 Change Units Label 58
- 9.5.4 Change 4 mA Value 59
- 9.5.5 Change 20 mA Value 59
- 9.5.6 Change Offset Value 59
- 9.5.9 Change Low Setpoint 61
- 9.5.10 Change High Setpoint 61
- 9.5.11 Set Up Delay Time 62
- Supported Modem Settings 68
- Default Modem Settings 68
- Configuring the Modem 68
- 9.9.1 Change Password 77
- Change the Password 77
- 9.9.3 Setup Site ID 78
- 9.9.4 Connect Battery 78
- 9.9.8 Factory Defaults 84
- 9.11 Manual Output Ctrl 88
- 9.12 Clear Alarms & Logs 89
- 9.12.3 Clear the Event Log 90
- 9.12.4 Clear the Trend Logs 90
- 85 Liebert 93
- A.2.1 Connection Methods 94
- A.2.2 Create a Connection 95
- COM1 Port Setup 96
- Properties Setup 97
- ASCII Setup 97
- A.3 OVERVIEW OF MENUS 99
- A.4 VIEW STATUS MENUS 100
- A.4.1 View Active Alarms 101
- A.4.2 View Alarm Log 102
- A.4.3 View Event Log 103
- A.4.4 View Trend Log 104
- A.4.5 View Input Status 105
- A.4.6 View Output Status 106
- A.4.7 View Pager Numbers 107
- Main Menu 108
- Back Up Alarm Log File 109
- Back Up Event Log File 110
- Back Up Trend Log Files 111
- A.6 SETUP MENU 112
- Setup Menu 113
- A.6.1 Setup Input 114
- A.6.2 Setup Common Alarm 116
- A.6.3 Setup Sensor 117
- Setup Sensor (continued) 118
- A.6.4 Setup I/O Matrix 119
- A.6.5 Setup Output 125
- Pager Setup 127
- Modem Setup 128
- A.6.7 Setup System Info 129
- Change Password 129
- Setup Site ID 130
- Connect Battery 131
- Setup Service Phone Number 132
- Factory Defaults 133
- Initiate Remote Alarm Test 134
- A.6.8 Connect Expansion Board 135
- A.6.9 Override Output 136
- Clear Active Alarms 138
- Clear the Alarm Log 138
- Clear the Event Log 139
- Clear the Trend Logs 139
- SL-31060_REV3_02-13 144
Produits connexes et manuels pour Unités d'alimentation électrique Emerson Liebert Remote Monitoring Panel
(48 pages)
(106 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.233 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels