Emerson Liebert Remote Monitoring Panel Manuel d'utilisateur Page 112
- Page / 144
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Setup Menu
Liebert
®
Universal Monitor
™
104
A.6 SETUP MENU
The Setup menu allows the user to configure the Universal Monitor—setting up inputs and outputs
and an input/output matrix to trigger actions, the modem and pagers, and system features such as
date and time. This menu also provides a vehicle for manually changing the state of an output to ON
or OFF, clearing active alarms and deleting records from the Universal Monitor’s alarm log, event log
and trend logs.
Main Menu
After connecting to the Service Terminal Interface, the Main Menu appears, as shown below.
• Choose 0 to access the features illustrated in this section.
Login Menu
The System and Control options require a password to prevent unauthorized users from making
changes to the system. After choosing 0 in the Main Menu above, the Login Menu appears:
• Enter the password, and the Setup Menu appears, as shown in the following section.
Main Menu
LIEBERT UNIVERSAL MONITOR
VX.XXX.X
LIEBERT CORPORATION COPYRIGHT 2003
ALL RIGHTS RESERVED
MAIN MENU
1=VIEW ACTIVE ALARMS
2=VIEW ALARM LOG
3=VIEW EVENT LOG
4=VIEW TREND LOG
5=VIEW INPUT & SENSOR STATUS
6=VIEW OUTPUT STATUS
7=VIEW PAGER NUMBERS
8=SILENCE ALARM
9=BACKUP LOG FILES
0=SETUP SYSTEM-LOGIN REQUIRED
SELECT A NUMBER:0
Login
YOU MUST LOGIN TO PERFORM
SETUP OR TO MAKE CHANGES
LOGIN WITH 4 CHARACTER
PASSWORD
>****
>INVALID PASSWORD, ENTER AGAIN
>PRESS <ESC> TO EXIT
>
- Universal Monitor 1
- TABLE OF CONTENTS 3
- 7.0 VIEW STATUS OPTIONS 4
- 10.0 SPECIFICATIONS 5
- 1.0 INTRODUCTION 9
- ALL CIRCUITS; 10
- ALL CIRCUITS: 11
- 1.7 Controller Board Overview 12
- POWER INPUT 14
- RELAY OUTPUTS 14
- 1.9 LED Indicators 15
- K4K3K2K1 K5 K6 K7 K8 16
- 1.11 Typical Sequence 17
- 2.0 INSTALLATION - MAIN BOARD 18
- Required tools 19
- 2.2.1 Mounting the Panel 19
- 2.3.1 Mounting the Panel 20
- Input Power Connections 22
- Packing Contents 24
- 3.2.1 Mounting the Panel 25
- 3.3.1 Mounting the Panel 26
- 4.1 Wiring Specifications 28
- (BOTTOM) 29
- 4.3 Connecting Analog Inputs 30
- TB10: COMMS 31
- 4.5 EIA422 Liebert SiteScan 32
- Web Connector 32
- 5.1 Wiring Specifications 33
- S4 S3 S2 S1 34
- EIA485 + (to UM-) 34
- EIA485 - (to UM+) 34
- POWER INPUT RELAY OUTPUTS 35
- 29 Liebert 37
- 6.0 OVERVIEW OF MENUS 38
- 6.1 Opening Screen Overview 39
- 6.2 Main Menu Overview 39
- 6.3 LCD Menu Overview 39
- 7.1 View Active Alarms 41
- 7.2 View Alarm Log 42
- 7.3 View Event Log 43
- 7.4 View Trend Log 44
- 7.5 View Input Status 45
- 7.6 View Output Status 46
- 7.7 View Pager Numbers 47
- 9.1 Login 51
- ↑↓=NEXT ↵=SELECT 52
- ↑↓=SELECT ↵=NEXT/END 52
- 9.2 Setup System - Overview 53
- 9.3.5 Set Up Delay Time 55
- 9.5.3 Change Units Label 58
- 9.5.4 Change 4 mA Value 59
- 9.5.5 Change 20 mA Value 59
- 9.5.6 Change Offset Value 59
- 9.5.9 Change Low Setpoint 61
- 9.5.10 Change High Setpoint 61
- 9.5.11 Set Up Delay Time 62
- Supported Modem Settings 68
- Default Modem Settings 68
- Configuring the Modem 68
- 9.9.1 Change Password 77
- Change the Password 77
- 9.9.3 Setup Site ID 78
- 9.9.4 Connect Battery 78
- 9.9.8 Factory Defaults 84
- 9.11 Manual Output Ctrl 88
- 9.12 Clear Alarms & Logs 89
- 9.12.3 Clear the Event Log 90
- 9.12.4 Clear the Trend Logs 90
- 85 Liebert 93
- A.2.1 Connection Methods 94
- A.2.2 Create a Connection 95
- COM1 Port Setup 96
- Properties Setup 97
- ASCII Setup 97
- A.3 OVERVIEW OF MENUS 99
- A.4 VIEW STATUS MENUS 100
- A.4.1 View Active Alarms 101
- A.4.2 View Alarm Log 102
- A.4.3 View Event Log 103
- A.4.4 View Trend Log 104
- A.4.5 View Input Status 105
- A.4.6 View Output Status 106
- A.4.7 View Pager Numbers 107
- Main Menu 108
- Back Up Alarm Log File 109
- Back Up Event Log File 110
- Back Up Trend Log Files 111
- A.6 SETUP MENU 112
- Setup Menu 113
- A.6.1 Setup Input 114
- A.6.2 Setup Common Alarm 116
- A.6.3 Setup Sensor 117
- Setup Sensor (continued) 118
- A.6.4 Setup I/O Matrix 119
- A.6.5 Setup Output 125
- Pager Setup 127
- Modem Setup 128
- A.6.7 Setup System Info 129
- Change Password 129
- Setup Site ID 130
- Connect Battery 131
- Setup Service Phone Number 132
- Factory Defaults 133
- Initiate Remote Alarm Test 134
- A.6.8 Connect Expansion Board 135
- A.6.9 Override Output 136
- Clear Active Alarms 138
- Clear the Alarm Log 138
- Clear the Event Log 139
- Clear the Trend Logs 139
- SL-31060_REV3_02-13 144
Produits connexes et manuels pour Unités d'alimentation électrique Emerson Liebert Remote Monitoring Panel
(48 pages)
(106 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.461 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels