Emerson 644 Spécifications Page 20
- Page / 182
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
10
Reference Manual
00809-0200-4728, Rev RA
Section 2: Configuration
April 2015
Configuration
Figure 2-1. Powering the Transmitter for Bench Configuration
A. Power Supply
B. Field Communicator
Note
Signal loop may be grounded at any point or left ungrounded.
A Field Communicator may be connected at any termination point in the signal loop.
The signal loop must have between 250 and 1100 ohms load for communications.
Max torque is 6 in.-lbs (0.7 N-m)
2.4.2 Choosing a configuration tool
Configuring with a Field Communicator
The Field Communicator is a hand-held device that exchanges information with the transmitter
from the control room, the instrument site, or any wiring termination point in the loop. To
facilitate communication, connect the Field Communicator, shown in this manual, in parallel
with the transmitter (see Figure 2-1). Use the loop connection ports on the rear panel of the
Field Communicator. The connections are non-polarized. Do not make connections to the serial
port or the Ni-Cad recharger jack in explosive atmospheres. Before connecting the Field
Communicator in an explosive atmosphere make sure the instruments in the loop are installed
in accordance with intrinsically safe or non-incendive field wiring practices.
There are two interfaces available with the Field Communicator: Traditional and Dashboard
interfaces. All steps using a Field Communicator will be using Dashboard interfaces. Figure 2-2
shows the Device Dashboard interface. As stated in “System readiness” on page 8, it is critical
that the latest DD’s are loaded into the Field Communicator for optimal transmitter
performance.
Visit www.emersonprocess.com to download latest DD library.
Turn on the Field Communicator by pressing the ON/OFF key. The Field Communicator will
search for a HART-compatible device and indicate when the connection is made. If the Field
Communicator fails to connect, it indicates that no device was found. If this occurs, refer to
Section 6: Troubleshooting.
644 Head Mount and Field Mount 644 Rail Mount
B
250 Ω ≤ R
L
≤ 1100 Ω
A
- Protocol 1
- Rosemount 644 3
- Temperature Transmitter 3
- Title Page 4
- Contents 5
- 6Section 6: Troubleshooting 8
- Reference Manual 10
- Table of Contents 10
- Section 1 Introduction 11
- 1.2 Overview 12
- 1.2.2 Transmitter overview 13
- 1.3 Considerations 14
- 1.4 Return of materials 15
- 1.5 Transmitter security 16
- Section 2 Configuration 17
- 2.3 System readiness 18
- 2.4 Configuration methods 19
- Configuring with an LOI 21
- 2.4.4 Failure mode 22
- 2.5 Verify configuration 23
- 2, 2, 8, 6 26
- 2.6.3 Setting output units 28
- Setting output units with LOI 29
- Communicator 30
- 2, 2, 3, 3 31
- Resetting Hot Backup 33
- 2.8 Configure device outputs 35
- 2.8.2 Damping 36
- 2, 2, 1, 5 2, 2, 1, 6 38
- Configuring tag with LOI 43
- 2.10.1 50/60 Hz filter 44
- 2.10.2 Resetting the device 44
- 2.11 Diagnostics and service 46
- 2, 2, 4, 3, 4 48
- AMS terms 49
- Configure min/max with LOI 50
- Special considerations 53
- Hot Backup 53
- 3.1 Overview 55
- 3.2 Safety messages 55
- 3.3 Considerations 56
- 3.4 Installation procedures 57
- 3.4.1 Set the alarm switch 58
- 3.4.2 Mount the transmitter 59
- 3.4.3 Install the device 60
- 4.1 Overview 67
- 4.2 Safety messages 67
- 4.3.1 Sensor connections 69
- 4.3.2 Power the transmitter 70
- 4.3.3 Ground the transmitter 71
- Shielding recommendations 72
- Option 2 73
- Option 3 73
- Grounded thermocouple inputs 74
- (HART/4–20 75
- Electrical Installation 76
- Figure 4-4. Load Limits 76
- 5.1 Overview 77
- 5.2 Safety messages 77
- 5.3 Calibration overview 78
- 5.4 Sensor input trim 79
- 3, 4, 4, 1 80
- 3, 4, 4, 2 81
- 5.5 Trim the analog output 82
- 3, 4, 5, 1 83
- 3, 4, 5, 2 83
- 5.7 Switching HART Revision 86
- Section 6 Troubleshooting 87
- 6.4 Diagnostic messages 90
- (SIS) Certification 93
- 7.4 Commissioning 94
- 7.5 Configuration 95
- 7.7.1 Proof test 96
- 7.7.2 Partial proof test 96
- 7.8 Specifications 98
- 7.8.3 Product life 99
- A.1 Specifications 101
- A.1.2 Physical 102
- OUNDATION 103
- A.1.3 Performance 104
- Sensor connections 105
- Communication requirements 106
- Power supply 107
- Temperature limits 107
- Turn-on time 108
- External transient protection 108
- Accuracy 108
- Accuracy example 110
- OUNDATION fieldbus 111
- 644H (DIN A Head Mount) 113
- 644 Field Mount 114
- 644 Rail Mount 114
- Sanitary Applications 117
- A.4 Ordering information 118
- 00809-0200-4728, Rev RA 123
- April 2015 123
- 2 NPT 00644-4438-0002 126
- 2 NPT 00644-4438-0102 126
- 2 NPT 00644-4438-0004 126
- 2 NPT 00644-4438-0104 126
- A.4.1 Configuration 127
- A.4.2 Tagging 127
- A.4.3 Considerations 127
- Custom configuration 128
- Head Mount 129
- A.5.2 Physical specifications 130
- Enclosure ratings (644H) 131
- Sanitary housing surface 131
- Load limitations 133
- Configuration 135
- ≤ Ta ≤ +85°C); Type 4X; 137
- 2-14 NPT) enclosure 137
- International 140
- Gas -40 °C ≤ Ta ≤ +65 °C 142
- Dust -40 °C ≤ Ta ≤ +85 °C 142
- T5 -40 °C ≤ Ta ≤ +70 °C 145
- T6 -60 °C ≤ Ta ≤ +40 °C 145
- T5 -60 °C ≤ Ta ≤ +85 °C 145
- Combinations 146
- Additional Certifications 147
- Product Certifications 149
- Sheet 2 of 2 158
- Trees and Fast Keys 165
- D.1 Number entry 173
- D.2 Text entry 174
- 175
- Canceling 176
- D.5 LOI menu tree 177
Produits connexes et manuels pour Mesure, test et contrôle Emerson 644
(92 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels