www.Fisher.comFisherr 2506 and 2516 Receiver/ControllersContentsIntroduction 2...Scope of Manual 2...
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 2014102. Install lock washers (key 83) on the cap screws (key 48). Then, insert the c
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201411Figure 11. Typical Transmitter and Receiver Installation with an Indicator and R
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201412Supply Connection WARNINGSevere personal injury or property damage may occur if
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201413See figure 3 for vent locations.A receiver/controller may be ordered with one of
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201414To start the system:D For all receiver/controllers, perform steps 1 and 2.1. Se
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201415To lower level or decrease density, rotate the knob in the opposite direction. T
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201416The factory sets this valve to relieve when the differential pressure between th
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 2014179. The output pressure should be 1 bar (15 psig) for a 0.2 to 1 bar (3 to 15 ps
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201418As long as the process level remains constant, the transmitter input pressure to
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201419The 2516F receiver/controller also features an anti‐reset windup valve. This val
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 20142IntroductionScope of ManualThis manual provides installation, startup, calibratio
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201420These letters correspond to: direct (D), reverse (R), snap (S), and proportional
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201421Table 5.Troubleshooting Chart (continued)Fault Possible Cause Check Correction4.
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 2014223. Secure the screws (key 96) and replace the tubing.4. Check all tubing conne
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201423Parts KitsKey Description Part NumberReceiver/Controller Repair Kits Contains ke
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201424Key Description Part Number 31 Nut, brass (2 req'd) 32 Flapper, K93602 nick
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201425Figure 14. Fisher 2506 and 2516 Receiver‐Controller Assemblies30A8956‐BC0670‐2SE
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201426Key Description Part NumberAnti‐Reset Windup Valve for2516F Only (figure 15)192
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201427Mounting PartsNotePart numbers are shown for recommended spares only. For partnu
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201428Emerson Process Management Marshalltown, Iowa 50158 USASorocaba, 18087 BrazilCha
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 20143Table 1. SpecificationsAvailable ConfigurationsFor additional information, refer
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 20144Table 1. Specifications (continued)Approximate Weight4.54 kg (10 Pounds)Declarati
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 20145Installation WARNINGTo avoid personal injury or property damage resulting from t
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 20146Actuator Yoke MountingSee figure 4 for a typical mounting plate. Key numbers are
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 20147Figure 6. Wall MountingAD4913‐HA3847‐1194(7.62)MOUNTINGPLATE (KEY 164)SPACER(KEY
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201481. Locate the receiver/controller mounting holes in mounting bracket (key 164, f
Instruction ManualD200129X0122506/2516 Receiver/ControllerApril 201493. Attach the mounting plate with receiver/controller to a 2‐inch (nominal) pipe
Commentaires sur ces manuels