Emerson Avocent Universal Management Gateway Guide de l'utilisateur Page 71
- Page / 146
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Administration.....65
Data logging
If you enabled Serial Session Logging under the Data Buffering tab, you will be able to download
the logged data once a serial session to the enable port has been launched.
To download logged data:
1. Click the Targets tab in the title bar.
2. From the sidebar, click Serial Console then click on the target on which you enabled data
logging.
3. Click the Logs tab, then click Download Logs.
-or-
The log files can be accessed or downloaded from the appliance shell in the directory /log/DB.
Serial PDUports
Autosensing ports can discover attached serial PDUs or, if autosensing is disabled, be configured
for serial PDUmode. See Port configuration on page 50 to configure a port.
To configure a serial PDU port:
1. Click Targets - Serial Management.
2. Under the Serial PDU Ports tab, click the checkbox for each port you want to configure.
3. Click the Edit button.
a. Use the drop-down list to select the PDU type.
b. Check the box to enable speed auto detection.
c. Configure the polling rate.
d. Enter the power cycle interval.
e. Use the drop-down menus to enable or disable Syslog, Buzzer and SW Overcurrent
Protection.
4. Click Apply.
Serial rack PDU
When connecting an appliance's autosensing port to a Cyclades™ PM10/20 or Avocent
®
PM PDU,
a straight CAT5/CAT6 cable should be connected to the In/Console port of the PM PDU.
- Installer/User Guide 1
- TABLE OF CONTENTS 3
- Table of Contents.....iii 5
- Product Overview 7
- Network and serial mode 8
- Web user interface (UI) 9
- VGA and USB connections 9
- CLI setup port 9
- IPv4 and IPv6 support 10
- Security 10
- Power management 10
- Auto discovery 10
- Flexible users and groups 11
- Installation 13
- Wall mounting 14
- Installation.....9 15
- Connecting the Hardware 17
- Connecting targets 18
- Installation.....13 19
- Turning On the Appliance 20
- Verifying the Connections 20
- Configuring the Appliance 21
- Configuration Example 22
- Descriptions 23
- Installation.....19 25
- Initial Appliance Setup 27
- Setting Up Your Network 28
- Firewall 29
- Port requirements 30
- Trellis™ 32
- Trellis™ platform 32
- Web User Interface 33
- Using the Sidebar 34
- Admin role 35
- Operator role 35
- User role 35
- Administration 36
- Defaults 38
- Network Settings 39
- Bridge Group Configuration 40
- OSPF and BGP 43
- Network Share 45
- User role group 45
- Password Policy 46
- Preemption Levels 46
- Adding a user 47
- Authentication 48
- Administration.....43 49
- User Target Access 50
- User Target Rights 50
- Managing user groups 51
- Appliance Administrator group 51
- Power User group 52
- User group 52
- Group Target Access 52
- Group Target Rights 53
- Manage Target Settings 54
- View Logs 54
- Administration.....49 55
- Licenses 56
- Port configuration 56
- Port assignment 57
- Serial Settings 58
- DHCP Settings 59
- Advanced settings 60
- Discovery 60
- Physical discovery 60
- Logical discovery 62
- Administration.....57 63
- Generic service processors 64
- Discovery log 65
- SPmanagement 66
- Default Users 67
- Access settings 67
- Serial management 68
- Serial console ports 69
- Data Buffering 70
- 0 with severity info 70
- Data logging 71
- Serial PDUports 71
- Serial rack PDU 71
- PDUmanagement 72
- Network PDU 73
- SNMPSettings 73
- Serial PDUs 74
- Asset Location 75
- UMIQ module 76
- Module settings 79
- Active sessions 80
- Default settings 80
- Administration.....75 81
- • AES - AES encryption 82
- Default Settings 83
- Target groups 85
- Firmware 86
- Backing up firmware 87
- USBDevices 88
- Com Digital Input 89
- Digital inputs 90
- Environment 90
- RS-485environment sensor 91
- PDU Temperature Sensors Delta 91
- Monitoring 92
- Digital Output 93
- Firewall and NAT 96
- Administration - Targets 97
- Defined networks 98
- Administration.....93 99
- Network - Hosts 101
- Add to add a new host 101
- Firewall and NAT - Hosts 101
- Services 102
- Administration.....97 103
- NATflow 105
- Firewall flow 106
- Firewall and NATflow 106
- NATsetup 108
- Firewall setup 109
- Number Description 111
- 1 Sidebar 111
- 2 Targets Table 111
- Service Processors 112
- Sessions 113
- Appliance 114
- Sessions tab 114
- Power capping 115
- UMIQ Modules 116
- KVM session optimization 116
- Targets.....111 117
- Serial Console 118
- Overview 119
- Settings 119
- Power Outlet 121
- Sensors and Events 123
- CPU and disk usage 124
- Appendices 125
- Appendices.....123 129
- Netboot Recovery 130
- #as the 131
- 0 for this parameter 131
- LAN performance 133
- WAN performance 133
- Bridge groups 134
- Hardware 134
- Network related 135
- Firewall and NAT on page 90 137
- Firewall and NAT 138
- Appendices.....133 139
- Apply when done 140
- /usr/bin/restartsnmpsvr 141
- Appendix L:Video Resolution 142
- Appendices.....137 143
- Technical Support Site 145
- About Emerson Network Power 146
Produits connexes et manuels pour Mise en réseau Emerson Avocent Universal Management Gateway
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels