Emerson XEV22D Manuel de service télécharger pdf (Page 4)

1592025920 XEV22D GB r3.0 02.02.2011.doc XEV22D 4/4

The instrument is provided with an internal check verifying memory integrity. Alarm “EE” will flash when

a failure in the internal memory is detected. In such case call the service.

15. TECHNICAL DATA

Housing: self extinguishing ABS.

Case: 4 DIN modules 70x135mm with male and female connectors; depth 60mm.

Mounting: DIN RAIL mounted in an omega (3) din rail.

Protection: IP20.

Connections: pluggable screw terminal block  2.5 mm

wiring.

Power supply: 24Vac/dc ±10%.

Power absorption: depending on connected valve 20VA max.

Display: three digits with icons, red LEDs, height 14.2 mm.

Inputs: 1 temperature probe:

PT1000 probe: -50 to 110°C (-58 to 230°F).

NTC probe: -40 to 110°C (-40 to 230°F).

1 pressure transducer: 4 to 20mA or 0 to 5V.

Digital inputs: 1 free of voltage.

1 high voltage.

Outputs for valve: bipolar or unipolar valves.

Data storage: on the non-volatile memory (EEPROM).

Kind of action: 1B.

Pollution degree: normal.

Software Class: A.

Operating temperature: 0 to 55°C (32 to 131°F).

Storage temperature: -25 to 60°C (-13 to 140°F).

Relative humidity: 20 to 85% (no condensing).

Resolution: 0.1°C or 1°F.

Precision a 25°C (77°F): ±0.7°C ±1digit.

16. STANDARD VALUES

Label Description Range Default Level

FtY Kind of gas

R22; 134; 404; 407;

410; 507; Co2

404 Pr2

Peo Probe Error opening percentage 0 to 100 % 50 Pr2

Ped Probe Error delay before stopping regulation 0 to 239 s; on on Pr2

tEU Type of Stepper motor uP; bP bP Pr2

tEP Automatic Valve configuration 0 to 10 1 Pr2

HFS Kind of driving HAF; FUL FUL Pr2

LSt Minimum number of steps 0; USt (*10) See tEP Pr2

USt Maximum number of steps LSt to 800 (*10) See tEP Pr2

ESt Extra steps in closing phase 0 to 255 (*10) 0 Pr2

Sr Step rate 10 to 600 step/s See tEP Pr2

CPP Current per phase (only bipolar valves) 0 to 100 (*10mA) See tEP Pr2

CHd Holding current per phase (only bipolar valves) 0 to 100 (*10mA) See tEP Pr2

oPE Start opening Percentage 0 to 100 % 85 Pr2

SFd Start Function duration 0.0 to 42min 00s, res. 10s 1.3 Pr2

Sti Stop regulation interval 0.0 to 24h 00min, res. 10min 0 Pr2

Std Stop duration 0 to 60 min 0 Pr2

MnF Maximum opening percentage 0 to 100 % 100 Pr2

FoP Forced Opening time-out 0 to 100 %; nU nU Pr2

PI PARAMETERS (trained staff)

Pb Proportional band

[0.1 to 50.0°C]

[1 to 90°F]

[10.0°C]

[50°F]

Pr2

rS Band Offset

[-12.0 to 12.0°C]

[-21 to 21°F]

[0.0°C]

[0°F]

Pr2

inC Integration time 0 to 255 s 120 Pr2

PROBE PARAMETERS

tPP Type of pressure transducer 420; 5V; LAn 420 Pr2

LPP Enable pressure probe sending in LAN n; Y n Pr2

PA4

Probe value at 4mA or at 0V (related to PrM

parameter)

[-1.0 to P20 bar]

[-14 to P20 psi]

[-0.5 bar]

[-7 psi]

Pr2

P20

Probe value at 20mA or at 5V (related to PrM

parameter)

[ PA4 to 50.0 bar]

[PA4 to 725 psi]

[11.0 bar]

[159 psi]

Pr2

oPr Pressure probe calibration

[-12.0 to 12.0 bar]

[-174 to 174 psi]

[0.0 bar]

[0 psi]

Pr2

ttE type of temperature probe PT1000; ntC ntC Pr2

otE Temperature probe calibration

[-12.0 to 12.0°C]

[-21 to 21°F]

[0.0°C]

[0°F]

Pr2

DIGITAL INPUTS

i1P Free of voltage digital input polarity CL; oP CL Pr2

i1F Free of voltage digital input function CCL; rL CCL Pr2

d1d Digital input 1 (free of voltage) activation delay 0 to 255 min 0 Pr2

i2P Main voltage digital input polarity CL; oP CL Pr2

i2F Main voltage digital input function CCL, rL CCL Pr2

d2d Digital input 2 (Main voltage) activation delay 0 to 255 min 0 Pr2

ALARMS

dAo Alarm delay after restarting regulation 0.0 to 42min 00s, res. 10s 10.0 Pr2

tdA Type of alarm signalled by relay ALL; SH; PrE; Di ALL Pr2

LPL

Lower pressure limit for superheat regulation

(related to PrM parameter)

[PA4 to P20 bar]

[PA4 to P20 psi]

[-0.5 bar]

[-7 psi]

Pr2

MoP

Maximum operating pressure threshold (related

to PrM parameter)

[LoP to P20 bar]

[LoP to P20 psi]

[11.0 bar]

[159 psi]

Pr2

LoP

Minimum suction pressure limit (related to PrM

parameter)

[PA4 to MoP bar]

[PA4 to MoP psi]

[-0.5 bar]

[-7 psi]

Pr2

PHy Pressure alarm Hysteresis

[0.1 to 5.0 bar]

[1 to 72 psi]

[0.1 bar]

[1 psi]

Pr2

dML delta MoP-LoP 0 to 100% 30 Pr2

MSH Maximum superheat alarm

[LSH to 80.0°C]

[LSH to 176°F]

[80.0°C]

[144°F]

Pr1

LSH Lowest superheat alarm

[0.0 to MSH°C]

[0 to MSH°F]

[2.5°C]

[2°F]

Pr1

SHY Superheat hysteresis

[0.1 to 25.5°C]

[1 to 77°F]

[0.1°C]

[1°F]

Pr2

SHd Superheat alarm activation delay 0 to 255 s 120 Pr1

FrC Fast-Recovery Constant 0 to 100 s 50 Pr2

DISPLAY

Lod Local display SH; PEr; P1; P2 SH Pr1

CF Temperature measurement units °C; °F

[°C]

[°F]

Pr2

PMu Pressure measurement unit bAr; PSi bAr Pr2

rES Resolution (only °C) dE; in dE Pr2

PrM Type of pressure (Absolute / relative) rEL; AbS rEL Pr2

CLP Cooling call percentage Read only - - - Pr2

tP1 Temperature probe value Read only - -- Pr1

PPr Pressure probe value Read only - - - Pr1

tP2 Temperature converted from pressure probe Read only - - - Pr1

oPP Acutal Opening percentage Read only - - - Pr1

d1S Free of voltage digital input state Read only - - - Pr1

d2S Main voltage digital input state Read only - - - Pr1

Adr Serial address 1 to 247 1 Pr2

Mod Modbus type Std; AdU Std Pr2

Ptb Parameters map - - - - - - Pr2

rEL Release software - - - - - - Pr2

Pr2 Second level menu - - - - - - Pr1

1 2 3 4

Commentaires sur ces manuels

Pas de commentaire

Emerson XEV22D Manuel de service Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Mesure, test et contrôle Emerson XEV22D