Emerson NXr Manuel d'utilisateur Page 21
- Page / 112
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Electrical Connections
13
2.1.7 Cabling Procedure
Once the equipment has been positioned and secured for operation, and the battery and ground col-
lars have been connected (see 2.1.4 - Cable Connections), connect the power cables as described
below. (Study the reference drawing in 6.0 - Installation Drawings.)
1. Verify that all incoming high and low voltage power circuits are de-energized and locked out or
tagged out before installing cables or making any electrical connections.
2. Remove the left side panel to gain easier access to the connections busbars.
3. Connect the safety ground and any easier bonding ground bus cables to the copper ground busbar
located on the bottom of the equipment below the power connections. All cabinets in the UPS
system must be connected to the user’s ground connection.
4. Identify and make power connections with incoming cables according to Steps 5 through 11.
Common Input Connections
5. For common bypass and rectifier inputs, connect the AC input supply cables between the power
distribution panel and the UPS input busbars (A-B-C terminals) and tighten the connections to
44 lb-in. (5 N-m) using the M6 bolt provided.
6. The input neutral cable must be connected to the input neutral busbar (N). See Figure 5.
Dual Input Connections
7. For bypass connect the AC input supply cables between the power distribution panel and the UPS
input busbars (A-B-C terminals) and tighten the connections to 44 lb-in. (5 N-m) using the M6
bolt provided.
8. For Rectifier Input connect AC input supply cables between the power distribution panel and the
UPS input circuit breaker (A-B-C terminals)
9. The bypass and rectifier input neutral cables must be connected to the input neutral busbar (N).
See Figure 5.
Output System Connections—Ensure Correct Phase Rotation
10. Connect the system output cables between the UPS output busbars (A-B-C N terminals) and the
critical load and tighten the connections to 44 lb-in. (5 N-m) (M6 bolt).
!
CAUTION
The operations described in this section must be performed by authorized electricians or
qualified technical personnel. If you have any difficulties, contact your local Liebert
representative or Liebert Global Services.
NOTE
Hydraulic pressure pliers, combinative tools and piston ring pliers should be used to connect
AC wiring.
NOTE
The grounding and neutral bonding arrangement must comply with the National Electrical
Code and all applicable local codes.
NOTE
Both the rectifier and bypass feeds MUST come from the same utility source, except if the UPS
system includes either a configuration F or P external maintenance bypass cabinet.
!
WARNING
If the load equipment will not be ready to accept power on the arrival of the commissioning
engineer, then ensure that the system output cables are safely isolated.
- Liebert NX 1
- 2
- TABLE OF CONTENTS 3
- SAVE THESE INSTRUCTIONS 9
- Battery Cabinet Precautions 10
- GLOSSARY OF SYMBOLS 11
- 1.0 INSTALLATION 12
- 1.3 Preliminary Checks 13
- 1.4 UPS Location 13
- 1.6 Mechanical Considerations 14
- 1.6.1 Clearances 15
- 1.6.2 Floor Installation 15
- 1.6.3 Cable Entry 15
- 10-30kVA UPS 15
- System Composition 15
- 1.6.4 Optional Cabinets 16
- 2.0 ELECTRICAL CONNECTIONS 17
- 2.1.2 UPS Input Configuration 18
- 2.1.3 Cabling Guidelines 18
- 2.1.4 Cable Connections 19
- 2.1.5 Safety Ground 20
- 2.1.6 Protective Devices 20
- System Output 20
- 2.1.7 Cabling Procedure 21
- Common Input Connections 21
- Dual Input Connections 21
- 2.2 Control Cables 22
- 2.3 Dry Contacts 23
- 2.3.3 BCB Box Interface 24
- 2.3.4 Output Dry Contacts 25
- 2.3.5 EPO Input—Optional 25
- Firmware Before M200 25
- EPO - NO 26
- EPO - NC 26
- 3.0 BATTERY INSTALLATION 27
- Battery Installation 30
- 3.5 Non-Standard Batteries 32
- 4.1 Bypass Switch 33
- 4.2 Normal (UPS) Mode 33
- 4.3 Bypass Mode 34
- 4.4 Maintenance Mode 34
- 4.5 Locating the Cabinet 34
- 4.6 Cable Installation 34
- 4.6.3 Input/Output Wiring 35
- Maintenance Bypass Cabinet 36
- Terminal 36
- Location 36
- 4.7 Bolting Cabinets Together 37
- 5.0 OPTION INSTALLATIONS 38
- 5.2.1 General 39
- Option Installations 40
- 5.3.5 Power Cables 42
- 5.3.6 Parallel Control Cables 42
- Auxiliary Dry Contact Cables 42
- Input Distribution 43
- DPN U3813078 Rev. N 45
- Midpoint Busbar Detail 45
- Front View 45
- Bottom View 45
- 5.10.1 Configuring Baud Rates 48
- Figure 28 OC Web card display 49
- 3. UPS Battery is LOW 50
- 4. UPS fault has occurred 50
- 6.0 INSTALLATION DRAWINGS 52
- (with door open) 53
- TOP LAYER MIDDLE LAYER 56
- BOTTOM LAYER 56
- 1+1 Parallel Cabinet 59
- 1 + N Parallel Cabinet 61
- 7.0 OPERATION 66
- Operation 67
- 8.1 Operator Control Panel 68
- 8.2 Mimic Display Indicators 69
- 8.3 Control Buttons 70
- 8.4 Alarm Buzzer 70
- 8.5 LCD Overview 71
- 8.6 Navigation Keys 72
- 8.7 UPS System Information 72
- 8.8 LCD Menus and Data Items 73
- 8.9 Language Selection 74
- 8.10 Current Date and Time 74
- 8.11 UPS Status Messages 77
- 8.12 Types of LCD Screens 78
- 8.12.3 UPS Help Screen 79
- 8.12.4 Screen Saver Window 79
- 8.13 Pop-Up Windows 80
- 9.0 OPERATING INSTRUCTIONS 81
- 9.1.1 Power Switches 82
- 9.2 UPS Start Up 83
- 9.4 Powering Down the UPS 85
- Operating Instructions 86
- 9.7 Auto Restart 87
- 9.9 Battery Protection 88
- 9.15.2 Shutting Down the UPS 91
- 9.16 Parallel System Start Up 93
- 9.17 Replacing Dust Filters 93
- 10.0 UPS SPECIFICATIONS 94
- Table 27 UPS terminal 95
- 10.4.2 Input Rectifier 96
- 10.4.4 Inverter Output 97
- 10.4.5 Bypass Input 97
- 30 208 315 400 208 250 400 101
- PPENDIX A-UPS STATUS MESSAGES 105
- Refer to 108
- UPS Status Messages 110
- SL-25212_REV01_06-07 112
Produits connexes et manuels pour Alimentations sans interruption (UPS) Emerson NXr
(48 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.548 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels