Emerson 1500VA Manuel d'utilisateur télécharger pdf

Liebert

PSA

™

Quick-Start Guide - 1000VA/1500VA, 120V

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during

installation and maintenance of the UPS.

• Intended for installation in a controlled environment.

• Maximum ambient temperature 104°F (40°C).

• Do not connect equipment that may overload the UPS or demand half-wave

rectification, such as a laser printer.

• Connect the UPS only to an earthed / grounded outlet that meets national and local

electrical safety guidelines.

• Locate the UPS near a wall outlet. Do not use an extension cord between the UPS and

the outlet.

• The Liebert PSA has been designed for small office/home office use only; it is NOT

recommended for use in life-support applications.

• In the event of an emergency, press the OFF button and disconnect the power cord

from the AC power supply to properly disable the UPS.

• Do not attach power strips or surge suppressors to the UPS.

• Do not attempt to service any parts inside the UPS except the batteries. Failure to adhere

to this could cause personal injury or equipment malfunction and void the warranty.

• For technical support:

• Visit www.liebert.com or

• Send an e-mail to upstech@emersonnetworkpower.com.

SETUP

UPS CONTROLS AND CONNECTIONS

CAUTION

To reduce the risk of fire, connect only to a circuit provided with

20 amperes maximum branch circuit overcurrent protection in

accordance with the national code, ANSI/NFPA 70.

Step 1 Inspect the Package

Inspect the package and the UPS upon receipt. Notify the carrier and dealer of visible

damage.

Step 2 Decide Where to Place the UPS

The UPS must be placed indoors, protected from water, direct

sunlight and excessive heat.

Provide at least 4" (100mm) of clearance on all sides of the unit

for proper ventilation.

Step 3 Charge the UPS Battery Before

Use

The UPS battery is not charged before shipping. It MUST be charged before use.

• Connect the UPS power cord to a wall outlet and charge for at least eight hours.

Note: If battery is placed in storage, charge the battery every six months if kept at

5°F to 85°F (-15°C to 29°C)—or every three months if kept at 86°F (30°C) or higher.

Step 4 Start the UPS

After the battery is fully charged:

• Turn on the UPS by pressing the On/Off button (see Figure 1 below).

LED 1 should be illuminated (green), indicating the UPS is operating in Normal Mode.

Step 5 Check the Site Wiring Fault Indicator

See figure at right for the location of the Site Wiring Indicator on the rear of

the UPS.

• Check the rear of the UPS to make sure the Site Wiring Fault indicator is

NOT illuminated.

Caution: If the Site Wiring Fault indicator is illuminated, have a qualified

electrician check the wall receptacle wiring and fix any problems.

Step 6 Connect the Loads

The UPS has three battery backup outlets that

provide power when the UPS operates on battery

(see Figure 2 below).

• Plug the loads into the battery backup outlets

on the rear of the UPS.

Caution: Do not connect a laser printer to the

UPS.

Step 7 Connect the Network Surge Protection

The UPS has two RJ-45 jacks for network lines (see

Figure 2 below).

• Connect a single-line network cable into the RJ-45

network surge protection IN jack on the rear of the

UPS.

• Connect an RJ-45 cable from the OUT jack on the

rear of the UPS to a port on a PC or network device

such as a router.

Step 8 Set Up Liebert shutdown software

To start using the Liebert shutdown software:

• Install the Liebert shutdown software. See the software

user manual for installation instructions.

• Connect one end of the USB cable (supplied) to the USB

port on the rear of the UPS. Connect the other end to a

USB port on the computer. See the software user manual

for operating instructions.

UPS

USB

cable

Quick-start

guide

Liebert

shutdown

software

USB

Battery Power Supply

AC OUTPUT

AC INPUT

BREAKER

Full Time Surge Protection

IN OUT

SITE WIRING

FAULT

USB

Battery Power Supply

AC OUTPUT

AC INPUT

BREAKER

Full Time Surge Protection

IN OUT

SITE WIRING

FAULT

RS232

USB

Battery Power Supply

AC OUTPUT

AC INPUT

BREAKER

Full Time Surge Protection

IN OUT

SITE WIRING

FAULT

USB

Battery Power Supply

AC OUTPUT

AC INPUT

BREAKER

Full Time Surge Protection

IN OUT

SITE WIRING

FAULT

UPS Status, Alarm Conditions and Alerts

Condition LED Color Solid/Flashing Audible Alarm

Normal Mode LED 1 Green Solid (steady glow) (None)

Battery Mode LED 2 Amber Flashes every 3 seconds Every 3 seconds

Battery Low LED 2 Amber Flashes every 1 second till end of discharge (EOD) Every 1 second

Overload LED 3 Amber Solid (steady glow) until load drops or breaker trips Continuous

Battery Replacement LED 4 Red Flashes every 1 second for 5 seconds only Every 1 second for 5 seconds only

Fault LED 4 Red Solid (steady glow) until UPS shuts down after 5 seconds Continuous until UPS shuts down

LED 2

(amber)

EMERSON

™

Network Power

Liebert

PSA

AC Power System

USB

Battery Power Supply

AC OUTPUT

AC INPUT

BREAKER

Full Time Surge Protection

IN OUT

SITE WIRING

FAULT

LED 3

(amber)

Fault

symbol

Overload

symbol

Utility

symbol

On/Off

button

LED 1

(green)

Surge outlets (2)

NEMA 5-15R

USB

interface

Battery backup

outlets (6)

NEMA 5-15R

Input

breaker

Site Wiring

Fault indicator

LED 4

(red)

Battery

symbol

NEMA

5-15P

RJ-45 jacks (2) -

network protection

Figure 2 - Rear PanelFigure 1 - Front Panel LEDs

1 2

Résumé du contenu

Page 1 - UPS CONTROLS AND CONNECTIONS

Liebert® PSA™Quick-Start Guide - 1000VA/1500VA, 120VIMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONSThis manual contains important instructions th

Page 2 - SPECIFICATIONS

Modèles reliés 1000VA

Commentaires sur ces manuels

Pas de commentaire

Emerson 1500VA Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Emerson 1500VA. Emerson 1500VA User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 1000VA

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Emerson 1500VA