Emerson Liebert Remote Monitoring Panel Manuel d'utilisateur

AC PowerFor Business-Critical Continuity™HELPF4F3F2F1EMERSON™Network PowerLiebert®Press any key back to main menuLieber t NX081 kVA -3x312 - 16-2009Si

Installation62.6 Electrical connections Connect the power and communication cables to the RMP as shown in Figure 6.Figure 6 Power and communication ca

Installation7Connect the RS-485 communication cable to the Liebert NX as shown in Figure 7.Figure 7 RS-485 cable connection to Liebert NXConnect the o

Operation83.0 OPERATION3.1 Startup and ResetThe RMP will start as soon as the power supply is connected. The LCD will illuminate without any data disp

Operation9Figure 10 UPS and RMP firmware are compatible screenWhen the Silence On/Off button is pushed, the relevant screen in Figure 11 will be displ

Operation10Figure 12 Communication with UPS failedIf the RMP is functioning properly and the connection with UPS is correct, but the UPS does not sup-

Operation113.2 LED Mimic Power FlowThe LEDs mounted on the mimic flow chart represent the various power paths and current UPS oper-ational status.3.3

Operation123.4 Direct Access Push Buttons—KeysThe NX Remote Monitoring Panel has one direct access push button: Silence ON/OFF. The Silence ON/OFF but

Operation13The summary menu tree is shown in Figure 15. Refer to Table 12 for a detailed description of each menu item.Figure 15 Menu treeBatteryBatte

Operation143.6 Detailed Description of Menu Items The description that follows refers to the graphic LCD monitor window shown on Figure 14.UPS System

Operation15Current Record WindowKeeps a log the events that resulted in the current mode of operation. Ignores transient conditions that have been res

Operation163.7 Status and Event MessagesRefer to Table 13 for descriptions of events and alarms.Table 13 RMP messagesMessage Description / Suggested A

Operation17Inverter AsynchronousThis alarm is triggered by an inverter software routine when the inverter and bypass waveforms are misaligned by more

Operation18Bypass Phase ReversedThe phase sequence direction of bypass voltage is reversed.Normally, the phase of phase B lags 120 degrees behind phas

Operation19UPS Shutdown UPS Shutdown, output power-downCheck UPS Output Inverter off during normal startup (diagnostics information only)Generator Con

Operation203.8 Prompt (Popup) WindowsThe prompt window is displayed during the operation of the system to alert the user to certain condi-tions and /

Operation21Figure 16 Help screen3.10 Default screen saver This default screen is displayed following 2 minutes of operation with no new alarm or activ

Technical Specifications224.0 TECHNICAL SPECIFICATIONSTable 16 Mechanical specificationsMechanicalCharacteristics Units ValueHeight mm 100Width mm 400

Technical Specifications234.1 Agency and CertificationsSafety Standard: IEC/EN/AS 62040-1-1 incorporating applicable portions of IEC/EN/UL/AS 60950-1C

EmersonNetworkPower.comEnsuring The High AvailabilityOf Mission-Critical Data And Applications.Emerson Network Power, the global leader in enabling bu

iTABLE OF CONTENTSIMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1SAVE T

iiFIGURESFigure 1 Remote Monitoring Panel components and functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Figure 2 Re

1IMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONSThis manual contains important safety and operating instructions concerning the installation and

Introduction21.0 INTRODUCTIONThe Liebert NX Remote Monitoring Panel (RMP) is designed as a remote user interface to monitor Liebert NX Uninterruptible

Introduction3Figure 2 Remote Monitoring Panel layout constraintsTable 1 RMP component location in Figure 11 Bypass Input 10 F3 Function Key2 Inverter

Installation42.0 INSTALLATION2.1 Preliminary checksBefore beginning to install the RMP, verify that the equipment has reached site in its own packagin

Installation5Figure 4 Communication cable connection2.5 Mounting the RMP on DrywallTo hang the RMP on drywall or similar surface:1. Drill four holes (